106961-1301 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1069611301 1156013970


106961-1301 INJECTION-PUMP ASSEMBLY
Rating:
84
Buy INJECTION-PUMP ASSEMBLY 106961-1301 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 106961-1301 1069611301
ISUZU 1156013970 1156013970

Cross reference number

ZEXEL 106961-1301 1069611301
ISUZU 1156013970 1156013970


Zexel num
Bosch num
Firm num
Name
106961-1301 
106961-1302 
 
1156013970  ISUZU
INJECTION-PUMP ASSEMBLY
10PC1N *

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   8-3-600
Overflow valve opening pressure kPa   157 123 191
Overflow valve opening pressure kgf/cm2   1.6 1.25 1.95
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Right
  R
Injection timing adjustment
Direction of rotation (viewed from drive side)
Right
  R
Injection order   1-8-7-6- 5-4-3-10 -9-2
Pre-stroke mm   4.4 4.37 4.43
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-8
deg.   27 26.75 27.25
Difference between angles 2
Cal 1-7
deg.   72 71.75 72.25
Difference between angles 3
Cal 1-6
deg.   99 98.75 99.25
Difference between angles 4
Cal 1-5
deg.   144 143.75 144.25
Difference between angles 5
Cal 1-4
deg.   171 170.75 171.25
Difference between angles 6
Cal 1-3
deg.   216 215.75 216.25
Difference between angles 7
Cal 1-10
deg.   243 242.75 243.25
Difference between angles 8
Cal 1-9
deg.   288 287.75 288.25
Difference between angles 9
Cyl.1-2
deg.   315 314.75 315.25
Injection quantity adjustment
Adjusting point   A
Rack position   8.5
Pump speed r/min   750 750 750
Average injection quantity mm3/st.   87.2 85.7 88.7
Max. variation between cylinders %   0 -2 2
Basic   *
Fixing the lever   *
Injection quantity adjustment_02
Adjusting point   B
Rack position   8.7
Pump speed r/min   1000 1000 1000
Average injection quantity mm3/st.   102.5 100.5 104.5
Max. variation between cylinders %   0 -3 3
Fixing the lever   *
Injection quantity adjustment_03
Adjusting point   C
Rack position   8.2+-0.5
Pump speed r/min   1150 1150 1150
Average injection quantity mm3/st.   98.5 94.5 102.5
Max. variation between cylinders %   0 -3 3
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   D
Rack position   5.9+-0.5
Pump speed r/min   225 225 225
Average injection quantity mm3/st.   8.2 6.8 9.6
Max. variation between cylinders %   0 -13 13
Fixing the rack   *
Injection quantity adjustment_05
Adjusting point   F
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   133 133
Fixing the lever   *
Remarks
When manual lever is on the boost side
 
Timer adjustment
Pump speed r/min   900+50
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   1200
Advance angle deg.   6.5 6 7
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 106961-1301
N:Pump speed R:Rack position (mm) (1)Supply solenoid operating voltage DC24V and move the solenoid body so that the excess lever reaches the excess position at the solenoid's maximum stroke. (2)Supplied with damper spring not set. (3)At excess fuel lever operation: not exceeding EXL (4)Excess fuel setting for starting: SXL
----------
EXL=1.5mm SXL=10.2+-0.1mm
----------

Speed control lever angle

Test data 106961-1301
F:Full speed
----------

----------
a=7deg+-5deg

0000000901

Test data 106961-1301
F:Full load I:Idle (1)Stopper bolt setting
----------

----------
a=10deg+-5deg b=32deg+-3deg

Stop lever angle

Test data 106961-1301
N:Pump normal S:Stop the pump.
----------

----------
a=36deg+-5deg b=73deg+-5deg

0000001101

Test data 106961-1301
N:Normal B:When boosted
----------

----------
a=(5deg) b=(24deg)

Timing setting

Test data 106961-1301
(1)Pump vertical direction (2)Position of "Z" mark at the No 1 cylinder's beginning of injection (governor side) (3)B.T.D.C.: aa (4)-
----------
aa=13deg
----------
a=(170deg)




Have questions with 106961-1301?





Group cross 106961-1301 ZEXEL

Isuzu 

 
1156012401 
INJECTION-PUMP ASSEMBLY
10PC1N
106961-1301  

106961-1302 
 
1156013970 
INJECTION-PUMP ASSEMBLY
10PC1N
 
1156013971 
INJECTION-PUMP ASSEMBLY
10PC1N
 
 
INJECTION-PUMP ASSEMBLY
10PC1N
 
1156013973 
INJECTION-PUMP ASSEMBLY
10PC1
 
1156013974 
INJECTION-PUMP ASSEMBLY
10PC1
 
1156013975 
INJECTION-PUMP ASSEMBLY
10PC1
9 400 618 586 
1156013976 
INJECTION-PUMP ASSEMBLY
10PC1
Back to top