101603-8560 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1016038560 8943959021


101603-8560 INJECTION-PUMP ASSEMBLY
Rating:
61
Buy INJECTION-PUMP ASSEMBLY 101603-8560 zexel genuine, new aftermarket engine parts with delivery

Information injection-pump assembly

ZEXEL 101603-8560 1016038560
ISUZU 8943959021 8943959021

Service parts 101603-8560 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 101060-5130
3. GOVERNOR 105932-1080
4. SUPPLY PUMP 105210-6220
5. AUTOM. ADVANCE MECHANIS 105643-1060
6. COUPLING PLATE 105661-0840
7. COUPLING PLATE
8. _
9. _
10. NOZZLE AND HOLDER ASSY 105160-4282
11. Nozzle and Holder 8-94395-511-1
12. Open Pre:MPa(Kqf/cm2) 18.1{185}
13. NOZZLE-HOLDER 105030-4700
14. NOZZLE 105025-0530
15. NOZZLE SET

Include in #1:

101603-8560 as INJECTION-PUMP ASSEMBLY

Include in #2:

Cross reference number

ZEXEL 101603-8560 1016038560
ISUZU 8943959021 8943959021


Zexel num
Bosch num
Firm num
Name
101603-8560 
101603-8561 
 
8943959021  ISUZU
INJECTION-PUMP ASSEMBLY
6HH1-N * K

Calibration Data:

Adjustment conditions
Test oil
1404 Test oil
  ISO4113 or {SAEJ967d}
Test oil temperature degC   40 40 45
Nozzle and nozzle holder   105780-8140
Bosch type code   EF8511/9A
Nozzle   105780-0000
Bosch type code   DN12SD12T
Nozzle holder   105780-2080
Bosch type code   EF8511/9
Opening pressure MPa   17.2
Opening pressure kgf/cm2   175
Injection pipe
Outer diameter - inner diameter - length (mm)
mm   6-2-600
Overflow valve   131424-4920
Overflow valve opening pressure kPa   127 107 147
Overflow valve opening pressure kgf/cm2   1.3 1.1 1.5
Tester oil delivery pressure kPa   157 157 157
Tester oil delivery pressure kgf/cm2   1.6 1.6 1.6
Direction of rotation (viewed from drive side)
Left
  L
Injection timing adjustment
Direction of rotation (viewed from drive side)
Left
  L
Injection order   1-5-3-6- 2-4
Pre-stroke mm   3.4 3.35 3.45
Beginning of injection position
Governor side
  NO.1
Difference between angles 1
Cal 1-5
deg.   60 59.5 60.5
Difference between angles 2
Cal 1-3
deg.   120 119.5 120.5
Difference between angles 3
Cal 1-6
deg.   180 179.5 180.5
Difference between angles 4
Cyl.1-2
deg.   240 239.5 240.5
Difference between angles 5
Cal 1-4
deg.   300 299.5 300.5
Injection quantity adjustment
Adjusting point   -
Rack position   10.7
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   53 51.4 54.6
Max. variation between cylinders %   0 -2.5 2.5
Basic   *
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Injection quantity adjustment_02
Adjusting point   -
Rack position   9.7+-0.5
Pump speed r/min   275 275 275
Average injection quantity mm3/st.   9.4 8.1 10.7
Max. variation between cylinders %   0 -14 14
Fixing the rack   *
Standard for adjustment of the maximum variation between cylinders   *
Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.
 
Injection quantity adjustment_03
Adjusting point   A
Rack position   R1(10.7)
Pump speed r/min   850 850 850
Average injection quantity mm3/st.   53 52 54
Basic   *
Fixing the lever   *
Injection quantity adjustment_04
Adjusting point   B
Rack position   R1+0.1
Pump speed r/min   1400 1400 1400
Average injection quantity mm3/st.   64.5 60.5 68.5
Fixing the lever   *
Injection quantity adjustment_05
Adjusting point   C
Rack position   R1+0.45
Pump speed r/min   600 600 600
Average injection quantity mm3/st.   48.7 45.5 51.9
Fixing the lever   *
Injection quantity adjustment_06
Adjusting point   I
Rack position   -
Pump speed r/min   150 150 150
Average injection quantity mm3/st.   130 130 138
Fixing the lever   *
Rack limit   *
Timer adjustment
Pump speed r/min   550--
Advance angle deg.   0 0 0
Remarks
Start
 
Timer adjustment_02
Pump speed r/min   500
Advance angle deg.   0.5
Timer adjustment_03
Pump speed r/min   1000
Advance angle deg.   3 2.5 3.5
Remarks
Finish
 

Test data Ex:

Governor adjustment

Test data 101603-8560
N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT
----------
T1=K58
----------

Speed control lever angle

Test data 101603-8560
F:Full speed I:Idle (1)Use the pin at R = aa (2)Stopper bolt set position 'H'
----------
aa=35mm
----------
a=11deg+-5deg b=37deg+-3deg

Stop lever angle

Test data 101603-8560
N:Pump normal S:Stop the pump. (1)Use the pin at R = aa
----------
aa=45mm
----------
a=12.5deg+-5deg b=40deg+-5deg

Timing setting

Test data 101603-8560
(1)Pump vertical direction (2)Position of timer's threaded hole at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=14deg
----------
a=(160deg)




Have questions with 101603-8560?





Group cross 101603-8560 ZEXEL

Isuzu 

 
8943957520 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957521 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 610 659 
8943957522 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 611 600 
8943957523 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 619 951 
8943957530 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 619 849 
8943957531 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 270 
8943957532 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957540 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943957541 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 610 660 
8943957542 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 615 271 
1156029790 
INJECTION-PUMP ASSEMBLY
6SD1
9 400 615 272 
1156030240 
INJECTION-PUMP ASSEMBLY
6SD1
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

 
8943959010 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 610 661 
8943959011 
INJECTION-PUMP ASSEMBLY
6HH1-S
101603-8560  

101603-8561 
 
8943959021 
INJECTION-PUMP ASSEMBLY
6HH1-N
9 400 610 662 
8943959022 
INJECTION-PUMP ASSEMBLY
6HH1-N
 
8943959040 
INJECTION-PUMP ASSEMBLY
6HH1-S
9 400 610 663 
8943959041 
INJECTION-PUMP ASSEMBLY
6HH1-S
 
8943959051 
INJECTION-PUMP ASSEMBLY
6HH1-N
9 400 610 664 
8943959052 
INJECTION-PUMP ASSEMBLY
6HH1-N
 
8943959190 
INJECTION-PUMP ASSEMBLY
6HE1TC-S
 
8943959191 
INJECTION-PUMP ASSEMBLY
6HE1TC-S
9 400 610 665 
8943959192 
INJECTION-PUMP ASSEMBLY
6HE1TC-S
9 400 611 747 
8943959193 
INJECTION-PUMP ASSEMBLY
6HE1TC-S
Back to top