Rating:
Information
ZEXEL
101691-0850
1016910850
ISUZU
1156000070
1156000070
Cross reference number
ZEXEL
101691-0850
1016910850
ISUZU
1156000070
1156000070
| Zexel num | Bosch num | Firm num | Firm | Name |
|
101691-0850
101691-4200 |
1156000070 | ISUZU | * |
Calibration Data:
Adjustment conditions Test oil ISO4113 or {SAEJ967d}
1404 Test oil
Test oil temperature
degC
40
40
45
Nozzle
105780-0020
Bosch type code
DN4SD24T
Nozzle holder
105031-2010
Bosch type code
KB56SD273
Opening pressure
MPa
9.8
Opening pressure
kgf/cm2
100
Injection pipe
mm
6-2-600
Outer diameter - inner diameter - length (mm)
Outer diameter - inner diameter - length (mm)
Overflow valve
132424-0620
Overflow valve opening pressure
kPa
157
123
191
Overflow valve opening pressure
kgf/cm2
1.6
1.25
1.95
Tester oil delivery pressure
kPa
157
157
157
Tester oil delivery pressure
kgf/cm2
1.6
1.6
1.6
Direction of rotation (viewed from drive side)
R
Right
Right
Injection timing adjustment Direction of rotation (viewed from drive side) R
Right
Injection order
1-4-2-6-
3-5
Pre-stroke
mm
2.2
2.15
2.25
Beginning of injection position
NO.1
Drive side
Drive side
Difference between angles 1
deg.
60
59.5
60.5
Cal 1-4
Cal 1-4
Difference between angles 2
deg.
120
119.5
120.5
Cyl.1-2
Cyl.1-2
Difference between angles 3
deg.
180
179.5
180.5
Cal 1-6
Cal 1-6
Difference between angles 4
deg.
240
239.5
240.5
Cal 1-3
Cal 1-3
Difference between angles 5
deg.
300
299.5
300.5
Cal 1-5
Cal 1-5
Injection quantity adjustment Adjusting point A
Rack position
13
Pump speed
r/min
600
600
600
Average injection quantity
mm3/st.
117.5
115.2
119.8
Max. variation between cylinders
%
0
-2
2
Basic
*
Fixing the lever
*
Injection quantity adjustment_02 Adjusting point B
Rack position
13
Pump speed
r/min
1000
1000
1000
Average injection quantity
mm3/st.
124
120.3
127.7
Max. variation between cylinders
%
0
-3
3
Fixing the lever
*
Injection quantity adjustment_03 Adjusting point C
Rack position
6.5+-0.5
Pump speed
r/min
225
225
225
Average injection quantity
mm3/st.
17.5
15.2
19.8
Max. variation between cylinders
%
0
-13
13
Fixing the rack
*
Timer adjustment Pump speed r/min 400+-50
Advance angle
deg.
0
0
0
Remarks
Start
Start
Timer adjustment_02 Pump speed r/min 600
Advance angle
deg.
0.6
0.1
1.1
Timer adjustment_03 Pump speed r/min 900
Advance angle
deg.
1.4
0.9
1.9
Timer adjustment_04 Pump speed r/min 1150
Advance angle
deg.
2
1.5
2.5
Remarks
Finish
Finish
Test data Ex:
Governor adjustment
N:Pump speed
R:Rack position (mm)
(1)Beginning of damper spring operation: DL
(2)RACK LIMIT: RAL
----------
DL=6-0.2mm RAL=13+0.2mm
----------
0000000901
F:Full load
I:Idle
S:Stop
----------
----------
a=4deg+-5deg b=9deg+-2deg c=46deg+-2deg
Timing setting
(1)Pump vertical direction
(2)Position of timer's threaded hole at No 1 cylinder's beginning of injection
(3)-
(4)-
----------
----------
a=(60deg)